Tricity Bendix TBG700X Manual de usuario

TBG 700UserManualGasHobGB

10Before any maintenance or cleaning can be carried out, you mustDISCONNECT the hob from the electricity supply.The hob is best cleaned whilst it is s

11The BurnersThe burner caps and crowns can be removed for cleaning.Wash the burners caps and crowns using hot soapy water, and remove marks with a

12Something Not Working?If the hob is not working correctly, please carry out the following checks before contactingyour local Service Force Centre.

13OVERALL DIMENSIONS Width: 680 mmDepth: 510 mmCUT OUT DIMENSIONS Width: 560 mmDepth: 480 mmSUPPLY CONNECTIONSGas:R 1/2 inch (1/2 inch male) Rear ri

14Burner Dia. Tap By-pass1/100 mmAuxiliary 28Semi-rapid 32Rapid 42Triple crown 56Aeration adjustment noneBURNER RAPID SEMI-RAPIDAUXILIARY TRIPLECROWNP

15Important safety requirementsThis hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations(Current Edition) and

16A) End of shaft with nutB) WasherC) ElbowFO0814FO 0264InstallationIMPORTANTThis hob must be installed by a competent person to the relevant GasStand

17It is important to install the elbow correctly, with the shoulder on the end of thethread, fitted to the hob connecting pipe.Failure to ensure the

18Building over a kitchen unit withdoorProper arrangements must be taken in designing thefurniture unit, in order to avoid any contact with the bottom

19Fitting the Hob into the WorktopCarry out the building in of the hob as follows:1. place the seals supplied with the hob on the front edge of the

2Thank you for selecting our applianceWe wish you lots of enjoyment with your new appliance and we hope that you willconsider our brand again when pur

20Electrical ConnectionsAny electrical work required to install this hob should be carried out by aqualified electrician or competent person, in accor

21Wiring Diagram21LN022024012345NPermanent ConnectionIn the case of a permanent connection, it is necessary that you install a double poleswitch bet

22Fault FindingPreliminary Electrical Systems CheckSTARTIsolate applianceand carry out:A: Earth Continuitycheck. Has inlet fuse blown?Carry out:C: Pol

23A. EARTH CONTINUITY CHECKAppliance must be electrically disconnected - meter set on W (Ohms) x 1 scaleand adjust zero if necessary.— Test leads fr

24Check gas supply atburnerIgnition System / Gas IgnitionYESCheck plug top fuse andreplace if necessaryCheck polarity and earthcontinuity of supply po

25CommissioningWhen the hob has been fully installed it will be necessary to check the minimum flamesetting. To do this, follow the procedure below.

26Conversion from Natural Gas to LPGIMPORTANTThe replacement/conversion from natural gas to LPG should only be undertaken bya competent person.It is i

27Standard Guarantee ConditionsWe, Electrolux, undertake that if within 12 months of the date of the purchase this Electrolux appliance orany part t

28Customer CareFor general enquiries concerning your Electrolux appliance, or for further informationon Electrolux products please contact our Custome

29This appliance is guaranteed by Electrolux in each of the countries listed at the back ofthis user manual, for the period specified in the applian

3ContentsImportant Safety Information ... 4Instructions for the User

30

31

3235674-6904 12/07 R.Awww.tricity-bendix.co.uk

4Important Safety InformationYou MUST read these warnings carefully before installing or using the hob. Ifyou need assistance, contact our Customer Ca

5 Ensure the control knobs are in the ‘OFF’ position when not in use. When using other electrical appliances, ensure the cable does not come into

61. Hob Top2. Semi-rapid Burner3. Triple Crown Burner4. Rapid Burner5. Auxiliary Burner6. Control KnobsDescription of the Hob2124 563

7INSTALLATIONAny gas installation must be carried out by a registered competent person,and in accordance with existing rules and regulations.The rel

8OperationHob burners control knobs The symbols on the knobs mean that :  there is no gas supply there is maximum gas supply there is min

9Burner minimum maximumdiameter diameterTriple crown 180 mm 260 mmLarge (rapid) 180 mm 260 mmMedium (semi-rapid) 120 mm 220 mmSmall (auxiliary) 80 m